High-country-tek emc-3 Manuale Utente

Page 1 of 39 emc-3 Controller Module User Guide – Rev A High Country Tek, Inc. reserves the right to improve this product at any time and without

Page 10 of 39 emc-3 Controller Module User Guide – Rev A Reverse Mode Operation A Reverse Cycle may be initialized either Manually or Automatical

Page 11 of 39 emc-3 Controller Module User Guide – Rev A Manual Control To manually control the Fan Banks, set “Manual Control Enable” to a numb

Page 12 of 39 emc-3 Controller Module User Guide – Rev A Inputs Command Inputs With only one exception, all command inputs have common settings:

Page 13 of 39 emc-3 Controller Module User Guide – Rev A Diagnostic ( digital ) Inputs ( ALL via 30 way ) There are eight digital inputs available

Page 14 of 39 emc-3 Controller Module User Guide – Rev A Outputs ( all via 18 way ) Output Bank Settings Each Bank has the following configuratio

Page 15 of 39 emc-3 Controller Module User Guide – Rev A Indicators Status LED The Status LED will Flash Red to indicate trouble codes. Module

Page 16 of 39 emc-3 Controller Module User Guide – Rev A % Current O/P LED STATE MEANING Off (Outputs Disabled) GRN (0-33%) YEL (34-66%) RED (

Page 17 of 39 emc-3 Controller Module User Guide – Rev A SAE J1939 CAN Messages All J1939 CAN messages for the EMC-3 can be either enabled or dis

Page 18 of 39 emc-3 Controller Module User Guide – Rev A HCT Status Message – enable/disable through the EE-Memory. This message is multiplexed an

Page 19 of 39 emc-3 Controller Module User Guide – Rev A Data Set 1 Byte 5 Bank 1 output % Offset = 0 Factor = 0.4 Byte 6 Bank 2 Output %

Page 2 of 39 emc-3 Controller Module User Guide – Rev A High Country Tek, Inc. (HCT) is North America’s foremost independent designer and produc

Page 20 of 39 emc-3 Controller Module User Guide – Rev A Current Configuration Message Format Transmission Cycle Time: 100mSData Length: 8Data P

Page 21 of 39 emc-3 Controller Module User Guide – Rev A emc-3 Configuration Message Multiplex Data Set Table 1st Data Set Byte 1 Mux Control 0

Page 22 of 39 emc-3 Controller Module User Guide – Rev AByte 2 Bank 2 Off DYCY Byte 3 Bank 2 Start DYCY Byte 4 Bank 2 Max DYCY Byte 5 Bank 2 R

Page 23 of 39 emc-3 Controller Module User Guide – Rev A 9th Data Set Byte 1 Mux Control 09h Byte 2 Manual Control Enable Byte 3 Bank 1 Manual

Page 24 of 39 emc-3 Controller Module User Guide – Rev A Appendix A, EE-Memory Configuration Codes Fire Input Enable Settings Code Description 0

Page 25 of 39 emc-3 Controller Module User Guide – Rev A Appendix B, Status LED Alarm Codes Code Description Controller Action 1 DG Input Activ

Page 26 of 39 emc-3 Controller Module User Guide – Rev A Appendix C, Settings and Limits EE-Memory Variable Min Max Description Coolant_Start_T

Page 27 of 39 emc-3 Controller Module User Guide – Rev ABank_2_Rev_DYCY 0 100 DYCY for Reverse Fan Operation Bank_3_Off_DYCY 0 Start - 1 D

Page 28 of 39 emc-3 Controller Module User Guide – Rev ABank_3_Control_1 0 7 Assignment for control input Bank_3_Control_2 0 7 Assignment

Page 29 of 39 emc-3 Controller Module User Guide – Rev A Appendix D, Electrical Characteristics Absolute Maximum Ratings Absolute Maximum Ratings

Page 3 of 39 emc-3 Controller Module User Guide – Rev A Introduction The emc-3 application allows for independent control of up to three fan bank

Page 30 of 39 emc-3 Controller Module User Guide – Rev A Appendix E, the Program Loader Monitor (PLM) 1) Introduction: The Program Loader Monit

Page 31 of 39 emc-3 Controller Module User Guide – Rev A Note: *.IMF files contain all of the DVC configuration information (i.e. Input

Page 32 of 39 emc-3 Controller Module User Guide – Rev A 2) Connecting the PC to the DVC Family: The DVC controller uses the RS232 standard to co

Page 33 of 39 emc-3 Controller Module User Guide – Rev A 3) Starting the Program Loader Monitor: From Windows press the “Start” button and then fr

Page 34 of 39 emc-3 Controller Module User Guide – Rev A 5) DVC Family Master Display: The Program Loader Monitor is used to observe the actual

Page 35 of 39 emc-3 Controller Module User Guide – Rev A When you Click in the Path Window, the window shown

Page 36 of 39 emc-3 Controller Module User Guide – Rev A Frequently Asked Questions: Description: DVC controller goes into programming mode when

Page 37 of 39 emc-3 Controller Module User Guide – Rev A ‘Wet’ Fluid Sensor Information

Page 38 of 39 emc-3 Controller Module User Guide – Rev A ‘Dry’ Fluid Sensor Information

Page 39 of 39 emc-3 Controller Module User Guide – Rev A

Page 4 of 39 emc-3 Controller Module User Guide – Rev A Table of Contents Introduction ...

Page 5 of 39 emc-3 Controller Module User Guide – Rev A 3) Starting the Program Loader Monitor: ...

Page 6 of 39 emc-3 Controller Module User Guide – Rev A Controller Mechanical information IMPORTANT NOTE: Recommended tightening torques for t

Page 7 of 39 emc-3 Controller Module User Guide – Rev A Theory of Operation Normal Operation At Power On, the module will not run the fans until

Page 8 of 39 emc-3 Controller Module User Guide – Rev A Wiring

Page 9 of 39 emc-3 Controller Module User Guide – Rev A PIN Name Function PIN Name Function PIN Name FunctionA1 RXD Recei veRS232Data‐Pin&a